Re: Xp Deus 2 HF2 Coil Videos - Tests and Hunts - Select Digging Guide see page 38
Posted: Sun Nov 15, 2026 3:31 am
You haven’t heard this talked about much have you. Remember the big 10k ring I found. I had swept looking at it in that park before I turned on my camera. You’ll hear my voice when I switch to 120 kHz highest single freq. I have never seen a target reporting in the range using lowest mf giving strong signal behave like this target did yielding around 6 ID rise reporting high 70s to around 80 using lowest MF. Not one target before. I would seen this before had I checked the junk ring I dug few days before but I didn’t check with highest single freq. I did show videos using square tabs and pull rings talking about this id behavior meaning they seem to read using highest single freq up closer to the id yielded using highest mf. Withing a few points. The other bigger 14k ring I have doesn’t behave like an equivalent reading pull ring using lowest MF. Biggest difference is ID yielded with higher single freq. 14 k reads lower vs pull rings compared to ID achieved using highest MF. This is what caused me to be very very suspicious of this ring (target). Had the ID rise going to highest MF and reported high in lowest MF. Yet 120 kHz Single freq was a bust. Meaning it read suspiciously low - closer to lowest MF even somewhat lower. And it turned out to be what? Hmm. Ole hick from the sticks.
Below is result of Google search with skin effect on a big 10k gold ring. And the search even mentions Deus 2 HF2 Coil as far as freq goes. I wonder if I would have done this search a year ago would this come up and mention this model and coil?
And that big ole 10k ring I found. Fits here huh. How it behaved with ID when I swept with different MF plus higher single freq (120 kHz).
At high frequencies—such as the 50 kHz to 90+ kHz range used by high-frequency metal detector coils—the skin effect restricts eddy currents to a very thin outer layer of a larger 10k gold ring, while leaving its thicker inner core largely unpenetrated. Because 10k gold is an alloy with relatively high electrical resistance compared to pure silver or copper, high-frequency waves penetrate slightly deeper into it than into high-conductivity metals, though still far less than the thickness of a heavy band.
How Skin Depth Affects a Heavy 10k Band
• Shallow Eddy Current Flow. At very high frequencies (around 80–90 kHz), skin depth in gold alloys shrinks to roughly 0.25 to 0.4 millimeters. On a thick, heavy 10k ring (like a men's wedding band or class ring measuring 1.5 mm to 3 mm thick), the electromagnetic field only excites the outer "skin" of the metal.
• Alloy Resistivity Factor. 10k gold contains 41.7% pure gold mixed with 58.3% alloy metals like copper, silver, zinc, or nickel. This mixture disrupts electron flow and increases electrical resistivity compared to pure gold or copper. Higher resistivity slightly increases the skin depth, allowing high frequencies to penetrate a bit further than they would on a thick silver ring of the exact same size.
• Reduced Core Contribution. Because the alternating current cannot reach the center of a thick band at high frequencies, the ring's total inner mass contributes less to the return signal. Only the surface area and the closed-loop geometry of the ring actively generate eddy currents.
Practical Impact on Metal Detecting (Target ID & Response)
• Strong Closed-Loop Eddy Currents. Even though the signal only rides the surface, a ring forms a continuous, closed circular loop. High frequencies energize this closed loop very efficiently, producing a sharp, clear target response and causing the Target ID (VDI) to jump noticeably higher when shifting from a lower frequency (like 29 kHz) up to a high frequency (like 53 kHz or 89 kHz) on non-normalized coils like the XP HF2 Coil.
• Differentiating from Thin Foil or Can Slaw. Thin aluminum foil or shredded can slaw is often thinner than the skin depth even at high frequencies, and it lacks a closed circular path. A thick 10k ring has plenty of metal depth to support the surface current all the way around its circumference, which helps it lock onto a stable ID jump where irregular trash flattens out or breaks up.
• Depth Trade-Offs. While high frequencies make a large 10k ring scream near the surface, extreme frequencies lose overall ground penetration in mineralized soil compared to mid-range frequencies (15–25 kHz). A heavy 10k ring buried very deep may actually hit stronger on a mid-frequency setting that penetrates both the soil and the full thickness of the gold band.
If you are testing a specific ring weight or band thickness against certain frequency shifts (like 29 kHz vs. 89 kHz), let me know the details and I can break down how its Target ID behavior compares to thick aluminum or brass trash.
Below is result of Google search with skin effect on a big 10k gold ring. And the search even mentions Deus 2 HF2 Coil as far as freq goes. I wonder if I would have done this search a year ago would this come up and mention this model and coil?
And that big ole 10k ring I found. Fits here huh. How it behaved with ID when I swept with different MF plus higher single freq (120 kHz).
At high frequencies—such as the 50 kHz to 90+ kHz range used by high-frequency metal detector coils—the skin effect restricts eddy currents to a very thin outer layer of a larger 10k gold ring, while leaving its thicker inner core largely unpenetrated. Because 10k gold is an alloy with relatively high electrical resistance compared to pure silver or copper, high-frequency waves penetrate slightly deeper into it than into high-conductivity metals, though still far less than the thickness of a heavy band.
How Skin Depth Affects a Heavy 10k Band
• Shallow Eddy Current Flow. At very high frequencies (around 80–90 kHz), skin depth in gold alloys shrinks to roughly 0.25 to 0.4 millimeters. On a thick, heavy 10k ring (like a men's wedding band or class ring measuring 1.5 mm to 3 mm thick), the electromagnetic field only excites the outer "skin" of the metal.
• Alloy Resistivity Factor. 10k gold contains 41.7% pure gold mixed with 58.3% alloy metals like copper, silver, zinc, or nickel. This mixture disrupts electron flow and increases electrical resistivity compared to pure gold or copper. Higher resistivity slightly increases the skin depth, allowing high frequencies to penetrate a bit further than they would on a thick silver ring of the exact same size.
• Reduced Core Contribution. Because the alternating current cannot reach the center of a thick band at high frequencies, the ring's total inner mass contributes less to the return signal. Only the surface area and the closed-loop geometry of the ring actively generate eddy currents.
Practical Impact on Metal Detecting (Target ID & Response)
• Strong Closed-Loop Eddy Currents. Even though the signal only rides the surface, a ring forms a continuous, closed circular loop. High frequencies energize this closed loop very efficiently, producing a sharp, clear target response and causing the Target ID (VDI) to jump noticeably higher when shifting from a lower frequency (like 29 kHz) up to a high frequency (like 53 kHz or 89 kHz) on non-normalized coils like the XP HF2 Coil.
• Differentiating from Thin Foil or Can Slaw. Thin aluminum foil or shredded can slaw is often thinner than the skin depth even at high frequencies, and it lacks a closed circular path. A thick 10k ring has plenty of metal depth to support the surface current all the way around its circumference, which helps it lock onto a stable ID jump where irregular trash flattens out or breaks up.
• Depth Trade-Offs. While high frequencies make a large 10k ring scream near the surface, extreme frequencies lose overall ground penetration in mineralized soil compared to mid-range frequencies (15–25 kHz). A heavy 10k ring buried very deep may actually hit stronger on a mid-frequency setting that penetrates both the soil and the full thickness of the gold band.
If you are testing a specific ring weight or band thickness against certain frequency shifts (like 29 kHz vs. 89 kHz), let me know the details and I can break down how its Target ID behavior compares to thick aluminum or brass trash.